The Cohu Ismeca NY20 is a pre-owned semiconductor test handler supplied for automated device handling and production-line integration. The actual input system, package tooling, test interface, output arrangement and installed functions depend on the specific machine available.
Are you considering the NY20 as a replacement for an existing handler or for a new product? Send your current machine model, a clear product or package photo and a brief description of your requirement. We can review the basic information first and continue with detailed matching only when necessary.
Cohu Ismeca NY20 Machine Information
| Manufacturer | Cohu Ismeca |
|---|---|
| Model | NY20 |
| Equipment Type | Semiconductor test and device handler |
| Condition | Pre-owned semiconductor equipment |
| Product Compatibility | Determined by the installed tooling and handling configuration |
| Actual Configuration | Confirmed according to the specific machine available |
| Delivery Scope | Based on the quotation and confirmed equipment list |
| Support | Initial fault review, parts matching and repair discussion |
| Shipping | Export packing and worldwide delivery |
Could the NY20 Fit Your Current Production Line
The important question is not only whether an NY20 is available, but whether the actual machine can handle your product and work with your current process.
For the first inquiry, you can simply provide:
The model of the machine currently used on your line
The product or semiconductor package name
A clear photo of the product or existing tooling
A brief explanation of the replacement, handling or testing requirement
Once the basic requirement is understood, we can continue checking the available machine and request further tooling or interface details only when needed.
What Is Included with the Available NY20
A pre-owned NY20 may have been configured for a particular semiconductor product or production line. Its feeder, package tooling, handling components, test interface and output system may therefore differ from another machine of the same model.
The actual configuration and supplied items will be confirmed according to the available machine. Only the equipment, tooling, cables and accessories listed in the quotation or confirmed delivery list are included.
An external tester, contactor, load board, special package tooling, computer or other production-line equipment should not be assumed to be included unless it is specifically stated.
What Should You Check When the NY20 Arrives
Complete a basic receiving inspection before installation or power-on.
Inspect the packing, machine cabinet, control screen, connectors and visible handling mechanisms.
Photograph any impact marks, loose parts, displaced assemblies or damaged cables before moving the machine.
Compare the received machine, tooling and accessories with the confirmed delivery list.
Confirm the electrical supply, grounding and other utility requirements of the actual machine.
Position and level the equipment before operating its loading or transfer mechanisms.
Any transport damage or missing item should be recorded before the machine is installed, modified or powered on.
Does the Machine Start and Cycle Normally
The first startup should confirm the basic machine condition before valuable semiconductor devices are introduced.
Start the controller and record any alarm messages before resetting the system or changing parameters.
Confirm that the machine completes initialization and returns its mechanisms to their home positions.
Run an empty cycle without loading production devices.
Observe the input mechanism, transfer movement, sensors and output actions throughout the cycle.
Stop the test if repeated alarms, mechanical interference, abnormal noise or unstable movement occurs.
The cause of abnormal operation should be reviewed before sample products are loaded.
Can the NY20 Handle Your Product Correctly
After the empty cycle is stable, use suitable samples or non-production devices that correspond to the installed tooling.
Check whether the product enters the machine correctly and remains in the required orientation.
Observe pickup, transfer, positioning and release during the handling sequence.
Confirm that the product reaches the intended output position without jams or incorrect placement.
If external test equipment is connected, check the interface signals and result handling.
Inspect the samples for scratches, terminal damage, impact marks or unstable handling.
Repeat several cycles to identify intermittent sensor, movement, pickup or output problems.
One successful cycle is not enough to confirm production readiness. The full handling sequence should remain stable without repeated alarms, product damage or incorrect output.
What If the NY20 Shows an Alarm or Handling Problem
Misfeeds, dropped products, positioning errors, jams or unstable handling may involve the tooling, sensors, motors, pneumatic components, pickup mechanism, controller or machine settings.
Stop operation if products are being damaged, mechanisms interfere with each other or the same alarm repeatedly returns. Record the alarm code, operating stage and visible symptoms before resetting the machine.
Send the machine model, alarm-screen photo, affected-area photos and a short video of the failed cycle where available. This gives our team a practical starting point for an initial fault review.
Repair and Ismeca NY20 Parts Support
If the NY20 develops startup alarms, feeding problems, unstable transfer, sensor faults or output errors, contact us with the machine information and a brief description of the problem.
Our team can assist with an initial fault review, help identify components that may require inspection and check related electronic or mechanical replacement parts where available.
Support may involve motors, drivers, boards, sensors, cables, pneumatic components, tooling or other handling assemblies. The appropriate next step depends on the actual fault, machine condition and available information.
Frequently Asked Questions
Can the Ismeca NY20 handle our semiconductor product?
This depends on the product and the tooling installed on the available machine. Send the current machine model and a clear product or package photo for an initial review.
What tooling and accessories are included?
Only the tooling, cables and accessories listed in the quotation or confirmed delivery list are included.
Does the machine include an external tester?
Not necessarily. External test equipment is included only when it is specifically listed in the confirmed delivery scope.
Is the used NY20 ready for immediate production?
Production readiness should be confirmed through installation, initialization, empty-cycle testing and repeated sample-product handling.
Can you assist if the machine has an alarm or requires repair?
Yes. Send the machine model, alarm information, affected-area photos and an operating video where available. We can assist with an initial review, parts matching and repair discussion.
Contact Us About the Cohu Ismeca NY20
Send your current machine model, a product or package photo and a brief description of your requirement or equipment problem. We will review the basic information first and continue with the necessary machine matching, replacement-parts or repair details afterward.
